FL3 Flash Copper Plating Kit 18 Litre

As of 1 October 2019 this kit does not include heaters.

Eliminates the use of cyanide strike coats. 

Eliminates the use of Pot Metal Primer on Zinc 

Eliminates the use of Nickel Strike on Steel prior
to copper plating 

Increases the bond of acid copper, Nickel and 
Copy Chrome™ to all substrates 

Flash Copper™ is a unique alkaline electrolytic 
copper plating process with covering 
and throwing powers greater than cyanide copper. 

Flash Copper™ is an outstanding pre-plate copper strike for bright nickel, acid copper, tin and solder plates. It is an excellent heat treat stop off plate and EMI shield.

It is also an excellent decorative finish for buttons, rivets, lighting fixtures and builders’ hardware. The copper plate can be readily blackened or oxidized for a variety of attractive antiqued finishes.

 

18.0 Litre Kit

1 x 20 litre Plating Tank & Lid 
Flash Copper™ Part A - 6 x 1 litre [6 Quarts ]
Flash Copper™ Part B - 3 x 500mL [ 3 Pint] 
Flash Copper™ Part C - 3 x 500mL [ 3 Pint]
2 x 100mm x 200mm [4" x 8"] Copper Anodes and bandages 
The Complete Plating Manual 
Free Technical Support 
  

There are no carbonates to be treated. It contains no strong chelators. It is supplied as a liquid concentrate, which is diluted with water.

Flash Copper™ produces a fine grained, smooth, dense and ductile copper deposit, which is nonporous and has excellent bonding properties. The throwing and covering power of the non-cyanide process is superior to cyanide processes. This is especially evident in barrel plating. It has uniform low current density distribution with excellent micro-throw.

The grain is smaller than cyanide copper, which increases the density of the deposit. This density provides excellent heat treat stop off and masking properties. The fine-grained Flash Copper™ deposit under nickel/chrome improves the overall corrosion resistance and helps to throw the nickel farther into the low current density areas.

Flash Copper™ produces a softer and more ductile deposit than cyanide or acid copper. The soft deposit imparts improved adhesion and corrosion resistance and greatly improved resistance to thermal shock. It has a high deposit purity and hence no out-gassing with subsequent brazing, soldering or vacuum operations.

Flash Copper™ is simple and inexpensive to use because it replenishes the copper in solution by dissolving the copper anode and here again it is a unique product with only one maintenance additive.

 

Flash Copper™ Benefits
One solution serves as both a strike and a plate bath. 

Greater throwing power than acid copper 

Eliminates the inherent dangers of cyanide in the work 
place and improves employee health and safety. 

Flash Copper™ has excellent bath stability and high efficiency. 

The bath does not have to be dumped as with other baths due
to breakdown products or iron buildup. 

The bath is easily maintained by monitoring the pH and copper
metal concentration. 

It has a very wide operating window. 

Flash Copper™ is supplied as a liquid concentrate, which is diluted 
with an equal amount of distilled water. 

 

YOU MUST SUPPLY


Power Supply  Caswell Australia Supplies these, follow the link
Heater
Copper Pipe for tank bar
Copper Wire to hang items
Small amount of electrical wire to make connections
Distilled water
Plugs for heater/s thermostat and pump if required
Heaters are usually supplied with a USA plug attached to suit the thermostat; or an Australian plug for any heater that is required to run direct to 240 vac. Leave the USA plug on for any heater that has to be temperature controlled.
All heaters, thermostats and pumps are 240 volt unless clearly labelled otherwise.
  • Because Flash Copper is usually used as a strike for other plating types, we do not include a degreaser.
  • If you require a degreaser, you can order our Aluclean Degreaser 
Price: $595.00
Quantity:
Total:  

Reviews

Your opinion is important to us...tell us what you think!

Review This Product